Commercial Cabinets & Casework in Cerritos, CA
If you are scoping commercial cabinets in Cerritos, you are probably holding a set of plans with a casework schedule on it and a deadline behind it. That is the work we do. Cerritos Custom Cabinets fabricates commercial casework in our own Cerritos shop, produces AWI-standard submittals and shop drawings for approval, and installs on your schedule, not ours. We are a licensed CSLB contractor, and our crews work both sides of the county line, covering commercial corridors across Los Angeles and Orange Counties.
General contractors, architects, facility managers, and tenants come to us for the same reason: one shop that quotes from drawings, builds what the submittal says, and shows up on the install date it committed to. Quoting is free and plan-based. Send the drawings and we price the package before anything gets cut.
Get a Free On-Site Design Consultation
Tell us about your project and we’ll schedule your free in-home measure and written quote.
Casework Fabrication, Not Catalog Boxes
Casework is the commercial trade term for cabinet units built to a project specification: base and wall cabinets, tall storage, countertops, and the millwork that ties them into the space. National suppliers sell it out of a catalog in fixed modules. We fabricate it. Every run is built to the dimensions on your drawings, in the laminate and hardware spec your project calls for, and delivered as a package sequenced to your construction schedule.
That difference matters most in the rooms that never match the catalog: a reception area with a radius wall, a break room squeezed between columns, an exam suite where every inch of storage is spoken for. A shop that fabricates to the drawing does not solve those rooms with filler panels. It builds to them.
Submittals and Shop Drawings to AWI Standards
Commercial casework lives or dies on paperwork. Before fabrication we produce shop drawings and submittals to AWI standards: elevations, sections, material and hardware schedules, and finish selections, issued for architect and GC review. You approve exactly what will be built, in writing, before a single panel is cut. When the field throws a surprise, and tenant improvement work always does, the drawings get revised and re-approved rather than improvised at the job site.
This is also where coordination problems get caught cheap. Blocking requirements, plumbing stub-up locations, electrical rough-in for transaction counters, ADA counter sections: all of it is resolved on paper during the submittal round instead of during install week.
Tenant Improvement Cabinetry on the GC's Schedule
Tenant improvement cabinetry is schedule-critical work. Your casework package lands in the middle of a trade sequence, after drywall and paint, before flooring transitions and final MEP trim, and a late cabinet shop stalls everyone behind it. We coordinate directly with the GC's schedule from the submittal stage forward, confirm delivery windows as the job progresses, and send install crews that hold their dates. When the superintendent calls, the shop that built the casework answers, because we are the shop that built the casework.
Typical commercial projects in our metro run $5,000 to $30,000, and scope drives that number more than square footage does. Laminate grade, hardware spec, ADA sections, and install phasing around other trades all move the bid, which is why we price from your drawings rather than from a rate card.
What We Build
Our commercial work breaks into five main lines, each with its own page and its own spec considerations.
Office Casework and Reception Desks
The front desk is the first thing a client sees and the hardest-working cabinet in the building. We build custom office cabinets and reception desks with transaction counters, locking lateral files, storage walls, and break room kitchenette runs, in brand-matched laminates with wire management planned before fabrication.
Dental Operatory Cabinets
Dental casework has its own rulebook: cleanable surfaces, tight operatory footprints, and storage for controlled materials. Our dental office cabinets are built around infection-control laminates, locking medication storage, and hardware rated for clinical duty cycles.
Medical and Exam Room Casework
Clinics, urgent care, and multi-provider suites need exam room casework and nurse station millwork that survives daily disinfection. Our medical office cabinets page covers exam rooms, nurse stations, and clinic storage in detail.
ADA-Compliant Cabinetry
Most shops retrofit accessibility onto catalog boxes after the fact. We build ADA-compliant cabinetry to the 2010 ADA Standards from the first cut: compliant counter heights, knee and toe clearance, reach ranges, and operable hardware, documented in the shop drawings so plan check goes smoothly.
Retail Display Cases and Store Fixtures
For storefronts and showrooms we fabricate custom display cases and store fixtures: showcases, cash wraps, slatwall millwork, and lighted feature walls, installed after hours so the store never closes for us.
Beyond those five lines, our custom millwork covers the architectural trim, paneling, and one-off pieces that finish a commercial interior.
HPL and TFL Laminate Systems
Almost all of our commercial casework is laminate over engineered cores, and the spec usually comes down to two systems. High-pressure laminate, HPL, is a separate sheet bonded to the substrate; it is the heavier-duty surface and the right call for countertops, transaction tops, and high-abuse verticals. Thermally fused laminate, TFL, fuses the decorative layer directly to the panel; it is economical, consistent, and well suited to cabinet bodies, shelving, and interiors. Most of our packages mix the two, HPL where hands and merchandise land, TFL where they do not, which keeps durability where it pays and cost where it does not.
Both systems come in the full commercial color and woodgrain ranges, so brand-matching a laminate to your interior palette is a selection, not a compromise. Edges are banded and machined in the shop, and every panel is cut on the CNC so parts arrive at the site ready to set.
Installed Across Los Angeles and Orange Counties
Our shop sits in Cerritos on the seam between the two counties, which is not a small logistical fact. A casework contractor based deep in one county treats the other as a long haul. We treat both as home turf: office parks in Cypress and Buena Park, medical corridors in Long Beach and Downey, retail in Anaheim, tenant improvement work anywhere along the 91, 605, and 5. Two-county reach from one Cerritos shop means one point of accountability for multi-site work on either side of the line.
From Plans to Punch List
Every commercial project runs the same sequence. You send plans, we return a quote priced from the casework schedule. On award, we produce AWI-standard shop drawings and submittals for approval. Fabrication runs in our Cerritos shop while your other trades do their work. We deliver and install on the coordinated date, then walk the punch list with your superintendent and close it out. A 5-year written workmanship warranty backs the package after handoff.
FAQs
What is a commercial millwork company?
A commercial millwork company fabricates and installs the built woodwork in commercial spaces: casework, cabinets, counters, paneling, and architectural trim. Unlike a cabinet retailer, it builds to project drawings and specifications, produces submittals for architect approval, and coordinates installation with the general contractor's trade sequence. We do all of that from our own fabrication shop in Cerritos.
How much do commercial cabinets cost?
Typical commercial cabinet and casework projects in our metro run $5,000 to $30,000. The spread comes from scope: laminate grade, hardware spec, ADA counter sections, and how installation phases around other trades. We price each package from your plans and shop drawings, so the number you get reflects your actual casework schedule, not a rate-card guess.
What is the difference between casework and millwork?
Casework refers to the box-based units: cabinets, counters, shelving, and storage built as repeatable assemblies. Millwork is the broader category of custom architectural woodwork, including trim, paneling, and one-off pieces built for a specific location. Most commercial projects need both, which is why we fabricate the full package in one shop under one set of drawings.
Do you work outside of Cerritos?
Yes. The shop is in Cerritos, and our install crews cover job sites across Los Angeles and Orange Counties. Sitting on the county line means neither side is a stretch for us, and multi-site rollouts that cross the line stay with one fabricator. Delivery and install phasing are coordinated with your GC regardless of which county the project sits in.
Send the Plans, Get a Number
If you have a casework schedule ready, send the plans and we will return a quote priced from shop drawings, free. If the project is still taking shape, schedule a walkthrough and we will scope it with you on site. Either way, call (562) 262-5720 and talk directly to the Cerritos shop that will fabricate, deliver, and install the work.